Very often you can hear the question why the chainsaw stalls at full speed. In simple terms, we can say that it simply cannot be adjusted (see here), while the full load setting simply cannot be changed. It should be done in such quantity that it can be fully developed in 1-2 weeks. The sawing units are idling, but the saw stalls when the gas is pressed, as the load increases. Adjusting The Chainsaw "Poulan 2150" Carburetor. Again, The starter is stationary and does NOT turn. It is a common situation that many owners find themselves in when the Stihl chainsaw does not start and fills in a candle. By continuing to use our site, you accept our use of cookies, For what reasons the Stihl MS 180 chainsaw will not start, Checking the pulse from the engine crankcase, There are sparks on the Stihl 180 Chainsaw, Algorithm for checking for lack of fuel supply, http://zemlyaselhoz.ru/pily/na-goryachuyu-ne-zavoditsya-pila-shtil.html, http://benzopilok.ru/brend/stihl/ms-180-ne-zavoditsya.html, Chainsaw Carburetor Adjustment Husqvarna 142, Speed Control Angle Grinder Without Power Loss. The most common reason is due to too many attempts trying to start the machine in the choke position. It works great, but is a real trick to start after sitting for several days/weeks. If, as a result of the examination, you find irregularities and chips, then this is a clear sign of breakage. With a defect in the crankshaft bearings, a slight backlash is observed on it. While the fully loaded jet is stationary. A similar problem can be solved quite simply, for which it is enough to remove the dirt using a needle. Only after checking the chain tension does the unit start. Speaking of dust 180, it must be said that this tool has many advantages. The gas expands in the tank, and I assume in the line etc, because it doesn't want to start until I open the gas cap a crack and let off the pressure. This is pretty easy to do. After that, the rotation is continued for another half turn in the same direction. over, this principle remains regardless of the operating conditions of the tool. Frequent malfunctions and methods of their elimination. Anyone who immediately rushes to disassemble the carburetor when the chainsaw does not start well on a hot one is at great risk. If the recoil starter assembly is defective, the engine won’t turn over and the chainsaw won't start. The tool is positioned for domestic use, which confirms the intensity of its use, which does not have to exceed 20 hours per month. Most likely, it has accumulated a lot of deposits associated with long-term operation of the tool, which is usually accompanied by the formation of exhaust. When you pull the starter rope, tabs extending from the pulley and cam should grab the hub on the engine, causing the engine to turn. After that, make 2 circles in the direction of the arrow. In the event that the supply hose and the fuel filter are normal, and the fuel supply is not observed, the reason may be hidden in a malfunction of the air pulse to the fuel pump. Very happy. And yet, the question of why the chainsaw does not start is absolutely impossible to answer. Stihl chainsaw is a clear choice for many homeowners and professionals due to its design and … In addition, it is often possible to observe a situation when the Stihl 180 chainsaw does not start hot and immediately stalls at the same moment or after a while. With the correct appeal, breakdowns appear in them occasionally and are quickly eliminated if the owner knows where to find the cause. In this case, most likely the reason is air leaks under the rubber pipe connecting the carburetor to the cylinder or its rupture. At the same time, the saw may stop starting if the tool chain is poorly lubricated. Regular maintenance will help to ensure that your Stihl chain saw will always start. In order to find out for sure that the problem is in the spark plug, it is necessary to check the known good one in the same way. At the same time, the filling of the fuel tanks with mixture and oil is controlled, the device is securely fixed in the hands. Saw won’t start: reasons and solutions. To make sure that the breather is NOT the cause of the malfunction, and it is in working order, you must. 95% of all chainsaw ‘problems’ are a result of ‘bad gas’ which usually means that the gas was left in the unit for several months or more.